-
BestCoat EP604 is an epoxy coating, solvent based, two components. It is
used for decorating and protecting to material surfaces such as: concrete,
brick, stone, wood, metal, composite panel…
-
BestCoat EP604 is applicable for: floor, slab, ceiling, wall, partition… of
store, garage, kindergarten, clean room, industrial production workshop or
places where requires the high capacity of chemical resistance, abrasion
resistance, dust and bacterium free.
-
Resistance to chemical, abrasion and dust…
-
Resistance to bacterium, moss and mould.
-
No blistering and no peeling.
-
High strength and qualified gloss.
-
Highly covering capacity.
-
Long lasting service.
|
Color:
|
Yellow, blue, green, brown, gray. (Color can be optional in accordance to the minimum required quantity) |
|
Density:
|
Part A+B: 1.33 ± 0.02 kg/liter @ 25oC (depend on color) |
|
Solid content:
|
Minimum: 65 % (by weight)
|
| VOC content: | ≤ 35% (by weight) |
|
Consumption:
|
0.10
÷
0.25 kg/m2 /layer (depend on surface condition)
|
|
Application
temperature:
|
Minimum temperature: 20oC (over dew point temperature of 5oC)
Maximum temperature: 35oC
Relative humidity ≤ 80% |
|
Chemical
resistance:
|
Resistance to alkali, acid, water, salt solution, oil, fuel and other common
chemicals.
|
| Mechanical strength : |
Resistance to dust and mechanical abrasion.
|
| Mixing ratio: | Part A : Part B = 4:1 (by weight) |
|
Preserve:
|
In cool, dry place |
|
Shelf - life : |
12 months from manufactured date |
| Packaging: | 30kg/set |
Pot-life:
|
Environment temperature
|
+20oC
|
+25oC
|
+30oC
|
+35oC |
|
Pot-life (minutes)
|
360 minutes
|
330 minutes
|
300 minutes
|
200 minutes
|
Curing times:
|
Environment temperature
|
+20oC
|
+25oC
|
+30oC
|
+35oC |
|
Waiting time Minimum
|
24 Hrs
|
18Hrs
|
12 Hrs
|
8Hrs
|
| Maximum |
No limited
|
No limited
|
No limited
|
No limited
|
|
Walkable
|
24hours | 18 hours | 12 hours | 8 hours |
| Light loading capacity | 2days | 2days | 1.5days | 1 days |
| Complete curing | 7days | 7days | 5days | 7days |
Coating
system:
For concrete, cement mortar, natural stone, synthetic stone surface:
- 01 layer of BestPrimer EP601: 0.10-0.25 kg/m2 /layer (depend on surface condition).
- 02 coating layer of BestCoat EP604: 0.10-0.25 kg/m2 /layer (depend on surface condition).
For metal surface:
- 02 coating layer of BestCoat EP604: 0.10-0.25 kg/m2
/layer.
Surface conditions:
- Concrete surface: Compressive strength: ≥ 20 MPa, tensile strength: ≥ 1.5 MPa. Surface should be flat, solid, steady, dry (moisture content ≤ 4%). Impurities, broken pieces, dust should be cleaned as required.
- Metal surface: should be free from rust, oil or impurities such as dust, water…
Mixing:
- Before applying, two components A and B should be properly mixed under the right ratio by slowly stirring (at speed of 300 500 rpm).
- Minimum mixing duration should not be less than 03 minutes and can be longer until reaching the required homogeneity.
- Take the mixtures about 10÷15
minutes then stirring again before application.
Application:
-
Apply by roller, brush or air-less sprayer.
- Notes:
Do not use mixtures over time to apply and get hardening.
Cleaning:
-
Use BestThinner SC-01 to clean equipment immediately after the execution and
before the mixture’s hardening.
Safety:
- Both two components are hazardous, flammable, therefore, should place away from heat or fire during the application and storage.
-
This product can cause allergic to skin, therefore should be prevented from
directly skin contact. Should wear gloves, masks and glasses while handling the
product.
-
In case of accidental eye contact, wash with fresh water and seek medical
advice immediately.