BestCoat EP707
Self-leveling epoxy, high strength, two components
Advantage:
-
Low viscosity, self-leveling and high gloss.
-
Allow application thin layer 1mm.
-
High mechanical properties.
-
Meet the requirement of standard: GMP, HACCP.
-
Resistance to chemical, impact , mechanical abrasion and heavy load bearing.
-
Easy to clean, wash, repair. Friendly to environment.
Download documents
EN VN
-
BestCoat EP707 is a two-component, non-solvent, self-leveling epoxy coating. It is based on 100% epoxy, mineral silicate and addictives.
BestCoat EP707 applies in these following:
- Sterile rooms, operating rooms, laboratories.
- Pharmaceutical or veterinary medicine factory.
- Food, brewery, aquatic or agricultural factory.…
- Electronic, computer, optics and accurate assembly plants.
- Chemical, insecticide factories.
- Kitchen rooms, Kindergardent.
-
Low viscosity, self-leveling and high gloss.
- Allow application thin layer 1mm.
- High mechanical properties.
- Meet the requirement of standard: GMP, HACCP.
- Resistance to chemical, impact , mechanical abrasion and heavy load bearing.
- Easy to clean, wash, repair. Friendly to environment.
|
Appearance/Color:
|
White, Yellow, Green, blue, and grey, are available, with special colors on
request.
|
|
Density:
|
1.60 ± 0.05kg/liter at 25oC (depending on colors) |
|
Solid content:
|
100% |
|
Application
temperature:
|
Minimum: + 15
oC (but above dew point temperature of 5oC)
Maximum: + 35oC
Relative humidity Max: 80% |
|
Consumption:
|
1.60 kg/m2
/mm thickness.
|
|
Mixing ratio:
|
Part A : Part B = 7:1 (by weight)
|
|
Preserve:
|
In cool, dry place (5oC ÷ 35 oC)
|
|
Shelf life:
|
12 months from manufacturing date in sealed package and stored in cool and dry place.
|
| Packaging: | 18; 36 kg/set. |
Pot-life:
|
Ambient temperature
|
+20ºC
|
+25ºC
|
+30ºC
|
+35ºC |
|
Pot-life (Minute)
|
90 |
65 |
40 |
30 |
Curing times:
|
Ambient temperature
|
+20ºC
|
+25ºC
|
+30ºC
|
+35ºC |
|
Walkable (Hr)
|
48
|
40
|
24
|
18 |
| Full cure (Day) | 10 | 08 | 07 | 07 |
Mechanical properties: (curing after 7 days @ 30ºC )
|
Compressive strength (MPa), (min.)
|
≥ 75
|
Flexural strength (MPa), (min.)
|
≥ 45
|
|
Tensile strength (MPa), (min.)
|
≥ 35
|
Bonding strength (MPa), (min.)
|
> 1.5
(Concrete failure)
|
|
Shore hardness (min)
|
≥ 75
|
Elongation (%), (min.)
|
≥ 0.5
|
Chemical resistance: (weight percent gained after immersion @ 20
oC)
|
|
H2O
|
10% NaCl
|
10% CH3COOH
|
10% H2SO4
|
10% NaOH
|
CH3OH
|
|
01 day
|
0.01
|
0.02
|
0.05
|
0.1 | 0.1 | 2 |
| 7 days | 0.05 | 0.04 | 1.5 | 0.3 | 0.4 | 4.2 |
Heat Resistant:
|
Temperature
|
Time
|
Temperature
|
Time
|
Temperature | Time | Temperature | Time |
|
+
50
ºC
|
Long
lasting
|
+ 75ºC |
ays
|
+ 100ºC | 12 hours | + 120ºC | 01 hour |
Coating system:
- 01 primer layer of BestPrimer EP701, BestPrimer EP702 or BestPrimer EP703.
01 layer of BestCoat EP707 with the thickness as design required.
Substrate requirement:
- To concrete surface: Compressive strength:
≥
20 MPa, tensile strength:
≥
1.5 MPa. Surface should be flat, solid, dry. The cracks, defective location must be treated, repaired, patched as required.
Mixing:
- Use an electric mixer or special blender at low speed (300÷400 rpm) to mix material about 03 minutes or longer until material is homogeneous.
- Note: If need to split quantity of material, should stir part A before weight.
Application:
- Pour the mixed mixture onto the corresponding surface area to each parallel rows with width 200 ÷ 300 mm, using a jagged scraper to spread out materials according to the thicknes required. Using a notched roller to support the leveling and get rid of air bubbles.
Note:
- While the mixture is not hardening, the application space should be no dust, avoid insects.
Cleaning:
- Clean tools, equipments with dry cloth and BestThinner SC01.
Safety:
- Product is non toxic, non flammable. Can be allergic to skin. Must be worn comforter, gloves, protective glasses.
- In case of accidental eye contact, wash with fresh water and seek medical advice immediately.