BestGrout E100

• Repair the concrete surface, filling holes.
  
• Filling the couplings bearing in the assembly structures, precast concrete,...
  
• Positioning bolts, anchoring machine foundation, rail pads, filling the baseplate ...
  
• In the case of tinting, BestGrout E100 is used as a floor finish for the purpose of load bearing, chemical resistance, abrasion resistance, mechanical impact resistance...

• High compressive strength, fast-growing.
• Non-shrinkage, non-crack.
• Excellent workability, flow ability.
• Bonding well with clean surfaces
• Chemical resistance, abrasion resistance,...
• Friendly environment 
  

Package:	31.5 kg/set (#15.0 liters/set) or as requested
Shelf life:	1 2 months from t h e date of manufacture, materials are sealed and stored in a cool place, and dry.
Color :	Natural grey (other special colors on requested).
Specific gravity:	2.1 ± 0.05 kg/liter (25oC) (depend on color)
Volatile Organic Compounds:	0 ÷ 2.5 mm
Application temperature:	Minimum: + 10⁰C (but above dew point temperature of 5⁰C)  Maximum: + 35⁰C Relative humidity: 80%
Mixing ratio:	A/B/C = 2.5/1/15 (by weight)

 Working time:

Ambient temperature:	+20⁰C	+50⁰C	+30⁰C	+35⁰C
Working time (minutes);	80	55	35	20

 Physical properties:

Flow-ability:	≥ 200                                                                                             (ASTM C230)
Compressive strength:	≥ 100 Mpa (after 07 days at 30oC)                                           (ASTM C579)
Flexural strength:	≥ 35 Mpa                                                                                       (ASTM C580)
Modulus of elasticity in flexure:	~ 12000 Mpa                                                                                (ASTM C580)
Adhesion strength:	≥ 1.5 Mpa (Concrete failure)                                                   (ASTM D7234)

 Chemical resistance (% weight increased after immersion in chemical solutions at 25oC):

Time:	H2O	10% NaCl	10% CH3COOH	10% H2SO4	10% NaOH	10% CH3OH
01 day	0.02	0.02	0.70	0.10	0.02	2.05
04 day	0.06	0.04	1.50	0.15	0.05	3.17
07 day	0.08	0.05	1.85	0.25	0.06	4.20

Surface condition:

• The material surface should be solidified and dry (the moisture is not more than 4%). Grease, dirt, rust, cement droppings ... must be completely removed.

Preparation for application:

• The slits or holes which are capable of sealing leaks must be sealed with the appropriate material. In the case of using the formworks and the surface in direct contact with the material should be isolated in PE layer in order to create favorable conditions to take off formworks later.
  

Mixing:

• Before application, two components A and B must be mixed thoroughly and continue to component C in accordance with the ratio of stirrer speed 300÷400 rounds/minutes. The mixing time is about 03 minutes or longer until homogeneous.
  

Placing:

• After mixing, use a steel trowel to stir lightly for a few seconds to release air bubbles. Then, the mixture is poured immediately into the prepared position to maintain the pressure necessary to avoid air entrapment in the mixture.
  

Note:

• Do not use material over time to allow application.
  

Cleaning:

• Use a dry cloth to clean the instruments, and equipment and wash again with BestThinner SC-01 before the mixture starts hardening. 

Safety:

• All three components are neither hazardous nor flammable. However, minimum safety requirements must be met when using the product.