BestSeal EP760

Self-Leveling compund based Epoxy-Cement, three components

Advantage:
  • Simple application, high effect. 
  • High bonding with all material surfaces(including moisture conditions). 
  • Waterproof, allow escape vapor. 
  • Anti-chemical, anti-oil, anti-mechanic,… 
  • Develop the strength quickly, put it into use early.
  • Allow coating the epoxy after curing for 24 hours. 
  • Non-toxic, odorless, and friendly with the environment.





Download documents          
                                                         EN                  VN

BestSeal EP760 is a self-leveling mortar, moisture resistance cement-epoxy based, high strength, three components.

BestSeal EP760 is used as a self-leveling mortar coating, thickness 1,5 ÷ 3,0 mm in following cases:

  • Temporary moisture-proof layer for the concrete surface in the protection coating based on epoxy.
  • Renewable the flatness or repair the damage of concrete floor,… 
  • Application for all floor surfaces which adhesion origin is cement and not enough time to cure...



  • Simple application, high effect. 
  • High bonding with all material surfaces(including moisture conditions).
  • Waterproof, allow escape vapor.
  • Anti-chemical, anti-oil, anti-mechanic,…
  • Develop the strength quickly, put it into use early.
  • Non-toxic, odorless, and friendly with the environment.

  Appearance / Color:

Part A: Milky white liquid

Part B: Viscous liquid

Part C: Pre-mixed dry powder/color white gray

Density:
Part A: 1.08 ± 0.02 kg/liter (25oC)
Part B: 1.01 ± 0.02 kg/liter (25oC)
Part C: 2.80 ± 0.02 kg/liter (25oC)
Part A+B+C: 2.20 ± 0.02 kg/liter (25oC)
Volatile organic compound:
0%

Consumption:

2.2 kg/m 2 /mm


Chemical resistance:
Resistant to water, saline room, oil and grease, liquid fuel and other general chemicals.
Mixing ratio:

A / B / C = 1 / 2 / 12.5 (By weight)

Storage Condition:

Store in a dry, cool place,  5oC ÷ 30oC

Shelf - life :

 12 months from date of manufacture

Package : 31 kg/set

Pot-life:

Temperature:
+20oC +25oC +30oC +35oC
Pot life
40min 20 min 15 min 10 min
Next coating and walking:
2 day 
 1.5 day 
 1 day 
  1 day
Light mechanical impact:
3 day 
 2.5 day 
 2 day 
 1.5 day 
Completely cured
28 day 28 day 28 day 28 day


construction techniques: 

  • Remove by grinding or chipping all cement dropping or concrete over pours, oil, grease,… 
  • The minimum tensile strength is 1.5 MPa.

Primer layer: ​

  • Use BestBond EP759 as a primer before application of BestSeal EP760 in cases of heavy load-bearing floors or highly porous surfaces.
  • Pre-coat BestSeal EP760 is needed if the surface is porous, soft, and high water absorbance.

Mixing:

  • Pour component B into a clean container of appropriate capacity (about 18 ÷ 20 liters). Shake part A well and pour to component B while the paddle is running, continue to pour slowly component C into the A + B mixture and mix until homogeneous (no lumps). Should mix with a slow electric or pneumatic mixer (300 ÷ 400 rpm).

Application:

  • Pour the mixed compound on the primer area, by parallel rows with width 200 ÷ 300 mm, use steel trowel or proper tools to distribute material according to the required thickness. Using a notched roller to support the leveling and get rid of air bubbles.
  • Note: Do not use material is over time to apply. Do not add any other material with BestSeal EP760.

Cleaning:  

  • Use fresh water and soap to wash equipments before and after application, before material gets hardening.

Safety:  

  • Three components is non-toxic but should wear gloves, safety glasses and masks while handling the product.
  • In case of accidental eye or mouth contact, wash with copious quantities of water and seek medical help or consult a doctor immediately.