BestCoat EP607

Self-leveling epoxy, high strength, two components

Advantages:
  • Low viscosity, high self-leveling and gloss.
  • Allow application with thickness about 1.0 mm. 
  • Meet the requirement of standard: GMP, HACCP.
  • Resistance to chemical, impaction, mechanical abrasion and heavy load bearing. 
  • Easy to clean, wash, repair…while using. 
  • Friendly to environment.





Download documents           
                                                   EN               VN
  • BestCoat EP607 is a two-component, non-solvent, self-leveling epoxy coating. It is based on 100% pure epoxy with mineral silicate and selective addictives.

BestCoat EP607 is applicable to concrete or metal floors with high requirements :

  • Sterile rooms, operating rooms, laboratories... 
  • Pharmaceutical or veterinary medicine factory... 
  • Food, brewery, aquatic or agricultural factory…
  • Electronic, computer, optics and accurate assembly plants… 
  • Chemical, insecticide factories,
  • Kitchen rooms, Kindergardent …



  • Low viscosity, high self-leveling and gloss.
  • Allow application with thickness about 1.0 mm.
  • Meet the requirement of standard: GMP, HACCP. 
  • Resistance to chemical, impaction, mechanical abrasion and heavy load bearing. 
  • Easy to clean, wash, repair…while using.
  • Friendly to environment.

Color:

 White, Yellow, Green, Blue, Grey, are available (optional on requested)

Density:
 1.60 ± 0.05 kg/liter at 25oC (depend on color).
Solid content:
100%

Consumption: ​

1.60 kg/m2 /mm thickness.

Application temperature:
Minimum: 15oC (above dew point temperature of 5oC)
Maximum: 35oC
Relative humidity ≤ 80%
Aggregate size:
Dmax: 75 µm
Flowability:
d ≥ 200 mm
Mixing ratio: Part A : Part B = 7 : 1 (by weight) ​

Preserve:

In cool, dry place

Shelf - life :

12 months from manufactured date

Packaging: 36 kg/set

Pot-life: ​

Environment temperature
+20oC
+25oC
+30oC
+35oC
Pot-life (minutes)
90 65
40
30

Curing time:

Ambient temperature
+20oC
+25oC
+30oC
+35oC
Walk - ability (Hr)
48
40 24 18
Full cure (Day) 07
07
07
07

Strength: (curing after 7 days @ 30oC)

Compressive strength (MPa)
≥ 70
Flexural strength (MPa)
≥ 35
Tensile strength (MPa)
≥ 25
Bonding strength (MPa)
Concrete failure
Shore hardness D
≥ 70 ​
Elongation (%)
≥ 0.5

Chemical resistance: (percent weight gained after immersion 20oC):

Time
H2O
10% NaCl
10% CH3COOH
10% H2SO4 10% NaOH CH3OH
01 day
0.01
0.02
0.50
0.10 0.01 2.00
07 days
0.05
0.04
1.50
0.30 0.04 4.20


Coating system:

  • 01 primer layer of BestPrimer EP601, BestPrimer EP602 or BestPrimer EP603.
  • 01 self-levelling layer of BestCoat EP607 with the thickness as design required.

Substrate requirement:

  • To concrete surface: Compressive strength: ≥ 20 MPa, tensile strength: ≥ 1.5 MPa. Surface should be flat, solid, dry. The cracks, defective location must be treated, repaired, patched as required.
  • Impurities, broken pieces, dirt, grease ... must be cleaned completely.

Mixing:

  • Pour part B into part A with the correct ratio. Use an electric mixer or special blender at low speed (300÷400 rpm) to mix material about 03 minutes or longer until material is homogeneous.
  • Note: If need to split quantity of material, should stir part A before weight.

Application:

  • Pour the mixed mixture onto the corresponding surface area to each parallel rows with width 200 ÷ 300 mm, using a jagged scraper to spread out materials according to the thicknes required. Using a notched roller to support the leveling and get rid of air bubbles.
  • Note: While the mixture is not hardening, the application space should be no dust, avoid insects.

Cleaning:

  • Clean tools, equipments with dry cloth and BestThinner SC01 before hardening.

Safety:

  • Product is non toxic, non flammable. However, this product can be allergic to skin, therefore should be prevented from direct contact to skin. It is advised to wear comforter, gloves, protective glasses while handling the product. In case of accidental eye contact, wash with fresh water and seek medical advice immediately.